Tactical Vest Flectarn size M Plate Carrier MOLLE "Shark"

Description: MOLLE Vest Tactical Body Armor Vest, color Flectarn, size M The threat level rating of the armor: NoManufacturer is Ukrarrmor Model "Shark" FmType: VestThe vest is equipped with MOLLYColor: Flectarn Size: MCondition: newMade in Ukraine Measurements:Chest Width: 12.5'' / 32 cmWaist Width: 16.1'' / 41 сmWaist circumference: 36-41'' / 91-104 cmHeight*: 5'10" - 6'1" / 176 - 185 cm * If you are taller, then you need the Medium long, if less, it means Meduim short version. Modular vest "Shark", has an improved ergonomic configuration of security elements and also allows to use them depending on the specific tasks and the likely threats. Very convenient and practical in the real world. On the entire surface of the bulletproof vest there is a webbing system MOLLE, to which equipment and ammunition can be attached. All belt lines MOLLE vest have the same color in the color of the vest. Webbing has maximum breaking loads. The "Shark" vest is a modular system and can be completely disassembled. Made from a very tough and high tenacity Cordura fabric. 1. Regulation and the composite vest "Shark" in the shoulder area, by means of a double hood valve fixed via Velcro Velcro element to protect the chest from above and below, allowing improved fixation. At the end of the shoulder, the edges of the valve, the attachment of the chest.2. Completion of bulletproof vests "Shark" can be supplemented with hard armor plates or soft Kevlar Ballistic Inserts (extra charge).3. On the inside of the cover in the flak vest there is a special bulky padding material with channels that allow air flow and remove moisture from the body.4. In the absence of removable side protection, the bulletproof vest is attached and adjusted at the waist with the help of a strap and textile fasteners (Velcro). The Klett Textile Museum completely eliminates this discomfort.5. The fastening of the left and right axle shafts of the side protection in the front has the double fixation with the textile fastener.6. Soft ballistic inserts and rigid armor plates can be placed in the side compartments.7. The left and right side elements of the body armor are protected by the MOLLE system from the back. This attachment allows you to adjust the bulletproof vest at the waist. So you can wear a vest in a winter T-shirt, and a warm volumetric jacket in winter.8. The bulletproof vest is equipped with a detachable neck protector, which consists of two parts.9. Pocket for armor plates. Vest has a pockets for the front and rear side of the vest. The size of the pockets is M (Medium) 10"x12" / 25x30 cm.The second pocket is designed to operate with maximum protection as it does not use soft Kevlar inserts.10. The vest has 7 rows of MOLLE slings, for which you can install all the necessary pockets, magazines, pockets for documents, a flashlight, walkie-talkie and other ammunition. You can also buy all these pounches in our ebay shop or on request if you can't find on our site. The standard version of the vest consists of 9 elements: The vest front, the vest rear, each side of the vest (left+right), the detachable shoulders and 2-piece neck collar, and the groin protector. For additional cost the vest can be completed:- soft ballistic inserts made with para-aramid fabric "Kevlar" according to the Ukrainian standard (DSTU) or the US standard. The soft ballistic inserts is in a sealed case of waterproof fabric and has protection over the entire surface of the body armor vest. - armor plates in accordance with the standard of Ukraine (DSTU) or the US standard. The hard armor plates are located in the extra pockets of the body armor vest. * In addition, the vest can be equipped with various pounches and Mags, as well as to increase the range of protective vests, by the following ingredients:- protection of the pelvis (coccyx) of the lower rear side;- deltoid axillary lateral zone elements;- camerbands for extra side plates; Hard plates and soft kevlar (aramid) ballistic inserts are not included in the cost of the vest and can be ordered at extra cost. But if you complete it soft ballistic inserts, than This model complies with NIJ Standard-0101.06 for Ballistic Resistance of Body Armor. We are manufacturers of these vests. We can manufacture your vest in absolutely any size from XS to 5XL or more. If you need another size, please contact us and we will make you an offer. If you have any questions, please ask, do not hesitate. So welcome to buy my lot. Enjoy your shopping, I still have a lot of other products of military and sporting themes.

Price: 205 USD

Location: Kiev

End Time: 2024-10-05T11:19:59.000Z

Shipping Cost: 35 USD