Description: ALL SCREW HEADS ARE SAME DIAMETER - EARLY / VINTAGE STAINLESS MODELS ONLY!! Up for sale is a Very Nice to Fine overall condition Vintage 3-Piece Sideplate Screw Kit (sometimes these are referred to as yoke screws) in Stainless Steel for the Smith & Wesson K, L and N Frame revolvers. These particular screws originated from a S&W Model 686 No Dash L-Frame revolver, but will work for many other S&W revolver models too, including many of the N Frame and K Frame models. Condition overall is quite favorable: The threads on these screws are all intact, the heads on the two Round Head Screws are nearly free of any evidence of tooling to the screw slots, and the Flat Head Screw (which is generally always covered by the grips anyway) shows only a minor amount of tooling to the Screw Slot. Priced per condition and scarce availability of a set in such favorable condition that has been out of production for over 30 years. To confirm, the buyer will receive all three items in the photographs that you see that make up this screw kit. The kit consists of the following screws (and measurements): - One (1) Round-Head Yoke (or Sideplate) Screw .368" L x .165" W head diameter - One (1) Round-Head Sideplate (or Yoke) Screw .365" L x .165" W head diameter (These first two screws could be interchanged depending on which is a better "match" for Yoke Stud Fitment - with the exception of this fractional difference in length, they are otherwise the SAME SCREW as each other! - One (1) Flat-Head Sideplate Screw .265" L x .165" W head diameter We ask to PLEASE NOTE: Later model revolvers used a Larger-Diameter Head "Yoke Screw" that was actually a Screw with a Spring-Loaded Pin assembled into the shaft of the Screw - this was part of an engineering change on later models to accommodate S&W's "New Yoke Retention System". Be aware of the differences, and if your original set does have the Front Yoke Screw (Front Sideplate Screw) with a larger head diameter than the other two - and a spring-loaded pin in the tip of it, then this set is NOT what you're looking for - unless it's used to replace the middle and rear-most screws only. Final Note: The appearance of the slightly larger two screws vaguely resembles a "strain screw" that happens to be located in the base of the grip of a S&W revolver, which typically measures much larger than the screws in this listing (strain screws are about 5/8 inches long) - please pay special attention to your application and do not go solely by the "look" of the screws in the pictures. We want you to get the correct item - These screws hold the Sideplate on to the frame! As with any vintage gun part there may be minor imperfections and we have attempted to capture a fair rendition of the condition of the item in the image set. See photos for full description. What is pictured is included in this listing: To confirm, the buyer will receive exactly the item as seen in this listing's photoset. It is up to the buyer to determine fitment / compatibility. Please contact us with any questions regarding compatibility / fitment, or condition PRIOR to bidding/buying as all sales on gun parts are final - and remember, we must ship only to your shipping address listed in your Ebay profile so please make sure your shipping address is verified and correct prior to purchase. Thanks for looking! ------------------------------------------------------------------------------------------------------------------------------------------- THESE PARTS COMPLY WITH EBAY'SFIREARMS AND ACCESSORIES POLICYAND ARE NOT "PROHIBITED ITEMS". ------------------------------------------------------------------------------------------------------------------------------------------------ The fine print: You are bidding on / purchasing the actual item(s) as seen in the photos for this listing. What you see is what you receive - no more, no less, unless stated specifically in the listing. If there are any questions about auctions / listings containing multiple items please inquire with us PRIOR TO BIDDING. We make every attempt at complete transparency as to what you are bidding on / purchasing and what you will receive. Sales to 48 Continental United States only. Additionally, we will cancel all sales to forwarding companies that ship outside of the USA. ALL SALES FINAL - CONFIRM YOUR SHIPPING ADDRESS: As a buyer on Ebay, you are accepting their terms and conditions that you must ship to a verified address that is currently listed as your "Ship To" address in your profile, and we (the Seller) MUST and CAN ONLY ship to that address. No post-sale updates to your shipping address will be permitted (this jeopardizes our Seller Agreement Terms and Protections), and requesting this change after the sale and payment is made will result in a formal complaint against your account with Ebay (unauthorized request by buyer), which may result in your access to the site being blocked - as well as a block for the sale to be refunded. All sales are final, unless specifically stated otherwise in the listing. By bidding or purchasing, you are agreeing to our terms and policies that are clearly stated below. Please read all of our terms and policies before placing a bid, making an offer, or purchasing this or other items from us. TERMS & POLICIES:In no event shall we, our officers, directors, employees and/or other representatives be liable for any damages of any kind, including without limitation, direct, indirect, compensatory, special, consequential, punitive, and/or incidental damages related to the products sold. All firearms parts should be inspected and installed by a competent gunsmith. The illegality or unenforceability of any provision of these Terms of Use shall not affect the validity and enforceability of any legal and enforceable provisions of these terms and policies. We have taken reasonable efforts to ensure that the information contained is accurate; however, all information is provided "as is" without any express or implied warranties, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non-infringement. In addition, by using the information from the listing, you understand and agree that all firearms are potentially dangerous if handled improperly and can pose risks and hazards to yourself and others, which may result in property damage, serious injury or death. Any advice, guidance or other information provided cannot completely anticipate your situation, and shall not create any warranty not expressly made herein, regardless of any omission or inaccuracy of information contained in our listings. You agree to defend, indemnify and hold the seller harmless against all third party claims, actions or demands, liabilities, and settlements, including, without limitation, reasonable attorney's fees, arising in connection with your use of this listing or resulting from, or alleged to result from, your use of the listings or your violation of these terms and policies.
Price: 24 USD
Location: Wausau, Wisconsin
End Time: 2024-12-02T15:36:49.000Z
Shipping Cost: 4.5 USD
Product Images
Item Specifics
All returns accepted: ReturnsNotAccepted
For Gun Make: Smith & Wesson
COMPATIBILITY NOTE: For VINTAGE Stainless Models Only - ALL HEADS SAME DIAMETER !!
Specific Part: Sideplate / Yoke Screws - 3 pc. Set
Color: Stainless
COMBINED SHIPPING REQUESTS - Message us: PRIOR to Purchase for a Listing Edit or Invoice.
MPN: Does Not Apply
Material: Stainless Steel
For Gun Model: Vintage K L N Frame Revolvers before "New Yoke Retention System"
Vintage: Yes
Brand: Smith & Wesson
Type: Action Parts
Features: S&W Factory Original Parts
For Gun Type: Revolver, Handgun
Country/Region of Manufacture: United States
Shipping To:: Continental 48 United States ONLY